Logo

P339C Engine Trouble Code

P339C Engine

When you check engine light came on code P339C the reason should be . However your vehicle's manufacturer may have a different definition for the P339C OBD-II Diagnostic Powertrain (P) Trouble Code. So you should chech it on our car models.

When the DTC check engine light comes P339C code on the first you can check is the gas related maybe gas cap. Pull over, retighten it, and take a look at the cap to see if it has any cracks inside. Go on driving and to see if the check engine light turns off automaticly. On the other hand, you can buy a gas cap for about $4.5 at an auto parts store. All you need to do is take the old one take off and take on the new one. If you've already bought it to the store, you might as well just replace the cap. While not car-threatening, it's good to take care of this right away to improve gas mileage/km.

P339C Code Meaning :

P
OBD-II Diagnostic Powertrain (P) Trouble Code For Engine
3
Ignition System Or Misfire
3
Fuel Rail Pressure Sensor Circuit Malfunction
9
Cylinder 4 Contribution/Balance Fault
c
Engine Shutoff Solenoid Malfunction

The oxygen (02) sensors on your car measure the oxygen in the exhaust to determine how rich or lean the ratio of fuel and air are in the cylinders. Optimizing this mixture means better fuel economy and fewer exhaust emissions.

P339C OBD-II Diagnostic Powertrain (P) Trouble Code Description

P339C engine trouble code is about Engine Shutoff Solenoid Malfunction. Fuel Rail Pressure Sensor Circuit Malfunction and Cylinder 4 Contribution/Balance Fault causes most of code P339C.

Reason For P339C Code

The reason of P339C OBD-II Engine Trouble Code is Fuel Rail Pressure Sensor Circuit Malfunction.

P339C DTCs may also be triggered by engine faults earlier down the line. For example, a dirty MAF sensor might be causing the car to overcompensate in its fuel-trim adjustments. As a result, oxygen sensors are likely to report fuel mixture problems.

How To Repair P339C Code

Before starting let's see P339C repairing process steps:

  • Qualified technicians will begin by using a scan tool to access P339C code stored in the ECU.
  • Technicians will note P339C code present and any freeze frame data associated with them.
  • After all, if you sure the engine trouble is finished, the code will be cleared.

A knocking sound that comes out of your bonnet is a definitive sign of an engine that is failing. Engine damage wear can cause this sound in your engine's technical components such as pistons, bearings or other motioning components.Some recurrent solutions for this situation might be in replacing the spark plugs, testing and replacing your ignition coils.

If nothing is done to repair the persistent P339C code, the ECU will put the vehicle into a limp mode. This mode limits the top speed and reduces engine power greatly to protect the engine.

Sometimes P339C code comes with P339C00 code.

Diagnosis Of Engine Error OBD Code P339C

It's essential to diagnose this trouble code. Then are some way which a handyperson should follow for diagnosing the problem that started a P339C trouble code to be stored

The first step is introductory and is about reacquiring all the canons that have been set. For this, the individual scanner will have to be plugged into the individual harborage of your vehicle. Make sure you indurate frame the data. Any canons that were set previous to the P339C code will have to be sorted first, as they may have been the reason for the law to set in the first place. It's always good to rule that out.

The coming step is to run a introductory examination of all the electrical circuits, connectors, wiring etc for damages similar as becks, erosion, fraudulent legs etc. All of these will have to be repaired or replaced. After that's sorted, clear the canons and go on a test drive to see if it resets. In case it resets, you'll have to continue your opinion. Depending on your vehicle you may have a vacuum operated selector or a vacuum solenoid if it's electrically actuated. In the case of the former, a hand held vacuum pump will have to be used to testit.The purpose is to see if the internal stopcock is getting turned by the selector, motor or solenoid. In order to do this, a command can be transferred to the system with scanner or by driving the vehicle under the special conditions that will spark the system. While this is passing keep an eye on the checkup tool data for the result.

All Engine Trouble Codes

All engine trouble codes with P, U, B and C engine codes.

Code Search

Please fill the "Code Box" to find engine fault code.

Example: 0140

Car Models :

Please select your car.

How To Read Engine Codes ?

Ways to read engine trouble codes.

How To Clear Check Engine Lights ?

Ways to clear check engine light on car panel.

Check Engine Light Dictionary

Ways to clear check engine light on car panel.